Skydive Mag is a free, international, online skydiving magazine with daily updates of news, event coverage, educational articles, safety information, videos and more

Pre-BASE-Season Checklist!

It’s that time of year again! Summer is just around the corner and BASE jumpers all over the world are pulling their gear out of the closet for the first time in months.

You went hard last year. Maybe you took a couple of trips, made regular visits to your local objects, or perhaps you were caught up in other adventures all season and your gear went largely underutilized. Regardless of your BASE activity level last year, a pre-season inspection is well-advised when it comes to life-saving equipment. So lay a tarp out in the backyard, make space in the garage, or move some furniture around in the living room to clear a packing area. Do whatever you need to do to make sure that your first canopy inspection in 2017 doesn’t occur while you’re in the saddle!

Do whatever you need to do to make sure that your first canopy inspection doesn’t occur while you’re in the saddle!
This is not a good place to question the condition of your gear!
This is not a good place to question the condition of your gear!

A word of caution:

This inspection should be more involved than your standard gear check. If you’ve spent any less than one hour combing over your rig you probably didn’t do a very thorough job. If you’re not up to spending that kind of time and attention we’d suggest you send it to a professional rigger instead of using this guide to pretend that you've completed a proper inspection.

Checklist

Assuming you’re starting with a packed rig, here’s a good checklist to work from. Make sure that the following components are in good condition and without signs of wear, abuse, or any other form of deterioration:

1. PC:

Check the ripstop for holes, burns and abrasions. Holding it up to the light will help expose potential problems. Inspect the mesh for tears. Be sure to inspect the bridle attachment point for wear, and that the PC is properly attached with a larks head knot. Remember the PC is the first thing out and the last thing packed. They are frequently dragged and seem to always end up in a bush after landing!

Hold your PC up to the light to inspect for damage to the ZP (or F-111) fabric.
Hold your PC up to the light to inspect for damage to the ZP (or F-111) fabric.

2 Bridle:

Check the full length of the bridle for wear and burns. If you’ve been doing static line jumps then extra attention should be given to check for abrasion and burn marks. Feel the pins for nicks which can damage your closing loops. Ensure that the pins are securely attached to the bridle and there is no damage to the retaining tab. Imagine for a second that one of your retaining tabs fails and a pin is left in the closing loop while your bridle trails behind you. That’s a bad situation, so pay close attention here.

3 Closing Loops & Grommets:

Extract the canopy from the container and examine closing loops for appropriate length and condition. While most manufacturers use all stainless steel grommets, we’ve seen more and more brass grommets out in the field. Brass is a softer metal and more easily damaged so pay close attention and ensure that there is no damage, nicks, or bends in any of your grommets.

4 Harness:

Inspect the harness webbing, hardware, and stitching. Look for wear on the webbing. Standard parachute industry hardware is durable but should be inspected for damage, burrs, and rust that may damage the webbing. Unlike cadmium, phosphate, and stainless steel; aluminum hardware is not a common parachute industry hardware and must be inspected carefully as it can crack. As lightweight hardware becomes more popular jumpers must start paying closer attention here and replacing hardware more frequently.

5 Risers:

Inspect your risers for damage. Make sure that the toggle Velcro is still in good condition and your links (hard or soft) are fastened appropriately. Make sure your 3 rings are assembled correctly and there’s no damage to the white loop.

6 Canopy Attachment Point:

Inspect for wear and ensure that your bridle is properly attached to the canopy with a larks head knot.

The attachment points on your bridle and PC should be free from wear and your PC should be affixed to the bridle with a larks head knot.
The attachment points on your bridle and PC should be free from wear and your PC should be affixed to the bridle with a larks head knot.

7 Canopy:

Before packing the canopy back into the container be sure to take your time and give it a thorough inspection for damage to seams and tears in the fabric. Holes larger than a quarter-inch (2 mm or 2 ripstop squares) should be professionally inspected. Whether or not a patch will be required is not only a function of the hole size, but also its location. Damage in load-bearing areas are more likely to require a patch than a hole on the top skin of an end cell, for example.

8 Lines:

Examine each one of your lines top-to-bottom to insure that they are free of damage and excess wear. Be aware that slider-up jumps will wear out your lines significantly faster than slider-off jumps. Check for fraying and melted areas which can result from lines rubbing together during deployment and opening.

All Velco, including tail pocket Velcro should be in good condition and free from wear and excess use. Worn tail pocket Velcro can cause hard openings and malfunctions.
All Velco, including tail pocket Velcro should be in good condition and free from wear and excess use. Worn tail pocket Velcro can cause hard openings and malfunctions.

9 Tail Pocket:

Examine the tail pocket Velcro for wear. Worn Velcro can result in line dump and hard openings which can create malfunctions which may damage canopies, lines, and jumpers.

Check Everything!

You’re starting to get the idea here. Check everything! This is a single parachute system that you’re trusting with life and limb, so take your time and make sure your gear is in proper working order. You’ll feel a whole lot better on the exit point if you do. Take notes or photos of wear points to catalog them and then ask for help if you are ever unsure!

This article was originally published on @joeputrino

Most Recent Articles

PD Factory Team: 15 Years

Dan'sMagic 16 - Jump Categories

Catching up with… Patrick Passe

Banish Big-way Brainlocks!

Sit to Head Down Back Flip Transition

Show more

Most Viewed Articles

Show more

advertisement

advertisement